Welltech SPCI2S Intel NetStructure SS7 Boards Manuel d'utilisateur Page 104
- Page / 107
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SS7 Programmer’s Manual for SPCI2, SPCI4 and CPM8 Issue 2 Page 104
A3 ISUP Parameters
A3.1 Global ISUP Configuration
Syntax: ISUP_CONFIG <res1> <res2> <user_id> <options>
<num_grps> <num_ccts> [<partner_id>]
Example: ISUP_CONFIG 0 0 0x2d 0x0435 4 128
The global configuration parameters for the ISUP module.
<res1>, <res2>
Reserved for backwards compatibility. These fields should be set to zero.
<user_id>
The module_id of the application running on the host that will use the ISUP module.
<options>
A 16 bit value containing global run-time options for the operation of the ISUP module. The meaning
of each bit is as defined for the ’options’ parameter in the ISUP Configure Request message as
detailed in the
ISUP Programmer’s Manual
<num_grps>
The maximum number of ISUP circuit groups that the user intends to use. This must not exceed the
maximum number of circuit groups supported otherwise module configuration will fail. Typically
<num_grps> should be set to the maximum number of circuit groups supported.
<num_ccts>
The maximum number of ISUP circuits that the user intends to use. This must not exceed the
maximum number of circuits supported otherwise module configuration will fail. Typically <num_ccts>
is set to 32 times the number of groups for E1 operation and 24 times the number of circuit groups
for T1 operation.
NOTE: The valid range for the circuit identifier (cid) is from zero up to one less than the maximum
number of circuits (num_ccts).
<partner_id>
Optional parameter for use when operating in dual resilient configuration. This parameter is the
module_id of the ‘partner’ ISUP module (equivalent to the ‘module_id field in the ISUP Configure
Request message as documented in the
ISUP Programmer’s Manual
).
A3.2 ISUP Circuit Group Configuration
Syntax: ISUP_CFG_CCTGRP <gid> <dpc> <base_cic> <base_cid> <cic_mask> <options>
<user_inst> <user_id> <opc> <ssf> <variant> <options2>
Example: ISUP_CFG_CCTGRP 0 3 1 1 0x7fff7fff 0x00000003 0 0x2d 2 0x8 4 0x00000000
The configuration parameters for a group of ISUP circuits. Usually a group is all the circuits on a
single E1 or T1 interface.
- NetStructure™ SS7 Boards 1
- SPCI4 and CPM8 1
- Contents 3
- Software Environment 16
- Programmer’s Manual 16
- 18 *(Decimal) 18
- 0x12 *(Hexadecimal) 18
- Synopsis: 39
- 4 Mb/s 0 .. 63 68
- 8 Mb/s 0 .. 128 68
- A1.2 LIU_CONFIG Command 93
- A1.3 LIU_SC_DRIVE Command 95
- A1.4 SCBUS_LISTEN Command 96
- A2 MTP Parameters 97
- A2.2 MTP Link Set 98
- A2.3 MTP Signalling Link 99
- A2.4 MTP Route 101
- A2.5 MTP User Part 103
- A3 ISUP Parameters 104
- A4 TUP Parameters 106
Produits connexes et manuels pour Communication Welltech SPCI2S Intel NetStructure SS7 Boards
(137 pages)Bowers & Wilkins Subwoofer Benutzerhandbücher
Beginnend mit A
Commentaires sur ces manuels