LP389 IP Phone Administrator Guide
Parameter Description: z Administrator: The administrator level user which has full access of LP389. z Supervisor: The supervisor level user which h
z Syslog Port: syslog server service port (default is 514) Auto Provisioning: The LP389 can be provisioned by WellEMS 9510 for large deployment.
VOIP Parameters Setting SIP Parameters: VOIP Setting > SIP Parameter Description: z Session Timer: Enable session timer or not (RFC 4028) z
SIP Timer Settings: (for advance user only) VOIP Setting > SIP Time Parameter Description: z SIP T1(msec): T1 determines several timers as def
z response upon receiving retransmissions of the request based on this timer. z Cancel General No Response Time(msec): When sending a CANCEL requ
SIP Line Settings SIP Line Account: SIP Lines > Line 1 to Line 3 Parameter Description: z Line 1~Line3: Up-to 3 separate SIP line can be u
16 z Outbound Proxy Server Port: SIP outbound proxy server UDP Port z Backup Proxy Server: Backup SIP registrar IP address z Backup Proxy Server P
Parameter Description: z Codec 1~5: The preferred codec priority z Codec Priority: Selection order to match the remote SDP for codec selection. -
SIP Line Call Preference: SIP Lines > Preference Parameter Description: z Record Missed Call: Record missed call or not. When enabled, the mi
SIP Lines > SIP Advance Parameter Description: z SIP Hold Type: SIP on hold message sending method. - Send Only: Set the SDP media to sendonl
2 Contents LOGIN LP389 ... 3 QUICK SETUP ...
20 “Stop Hunting Reason”, LP389 will try to use line 2 and then line 3 subsequently. * Per Line: When this mode is selected, you can use each line b
Phone Feature Settings Global Phone Voice Settings: Phone Setting > Voice Parameter Description: z Silence Suppression: Enable silence suppres
Parameter Description: z Headset Mic Volume: Headset microphone volume z Headset Volume: Headset output volume z Speaker Mic Volume: Speaker microp
Dialing Plan > General Parameter Description: z Inter Digit Time Out: If you are not using or match the dialed plan setting, the inter-digit tim
Parameter Description: z Matched Prefix: Called number party matched z Start Pos: Start position to be replaced z Stop Pos: Stop position to be r
Parameter Description: z Name: User name for the phone entry. This name will be used for name dialing features which support English only. z Tel N
Parameter Description: z Hot Line Function: Enable to disable hot line feature z Hot Line Number: The number to be dialed automatically after the
Column Description: z Tel no: calling telephone number z User Name: Caller’s user name if found in the phone book z Time: Calling time Received
Parameter Description: z Model: Model number z MAC-Address: Mac address z DHCP: DHCP is used or not z IP-Address: Current IPV4 address z IP
Parameter Description: z LAN Speed: LAN connected speed and status z PC Speed: PC connected speed and status z VLAN: Virtual LAN status Device
LOGIN LP389 QUICK SETUP Login to LP389: Setp1: Setup the administrative PC’s IP address to be s
Here provides a way to upload the customized ring tone and hold ton. Maintenance > Music Update For Ring Music, you can have Ring Tone Music 1 t
31
Fig.2 Change Default IP Network: Step 3: After successfully logon to the system, we need to change the network configuration. Click Device Setti
current date and time. Apply the change by clicking Apply button. (Fig.4) (Fig.4) Modify SIP Account Parameter: Step 5: The next step is to setup
(Fig.6) Check LP389 Registered Status: Step 7: After soft-reset. Click Status > Phone Status to check whether each line is registered or not. (
CONFIGURATION REFERENCE Device Settings Network Configuration Device Setting > Network Network: DHCP Networ
z Default Gateway: IPV4 Default gateway z VOIP VLAN: Enable VOIP VLAN or not z VOIP VLAN ID(2-4096): VLAN ID to be used z DNS Server1: Primary D
- Hour: 00 to 23 Device Advance Setting: Device Setting > Advance Parameter Description: z HTTP Port: The Administrator Web service port (the
Commentaires sur ces manuels