Welltech Dialogic SS7 Protocols ISUP Manuel d'utilisateur Page 152
- Page / 203
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Section 8 Non-Primitive Interface
152
gid mask
A mask of configured circuit groups where a bit’s position corresponds to a
circuit group id offset from the base gid and it’s value will indicate whether
the corresponding circuit group has been configured in ISUP or not. If the bit
is set, this indicates that the corresponding circuit group is configured.
8.15 Send Maintenance Event Mask Request
Sends a mask indicating which maintenance events should be active to the
ISUP module. All maintenance events are active when the module is
initialized. This message can be used to turn off some or all maintenance
events or turn them back on again. The message may be sent at any time
after the initial per-module configuration message has been sent to the ISUP
module.
Message Header
structure MSG
type ISP_MSG_S_MAINT_MASK (0x570f)
id 0
src Originating module ID
dst ISUP module ID
rsp_req Sending layer's bit set if confirmation required
hclass 0x00
status 0x00
err_info 0x00
len 9
Parameter Area
parameters offset 0, size 9: mask Bits set to indicate maintenance events which
should be active
ISUP Response
method By sending a MSG
type 0x170f
status SUCCESS
ISP_BAD_PARAM
Parameters
mask
A bit mask indicating maintenance events that are active. A ‘1’ indicates that
an event is active and a ‘0’ indicates that it is not active. The first octet sent
is for maintenance event codes 0-7, the second octet for maintenance event
codes 8-15, etc.
Refer to
Section : 8.19 Maintenance Event Indication on page 158 for a list of
maintenance events.
- Dialogic 1
- SS7 Protocols 1
- Contents 3
- Figures 6
- Revision History 7
- About this Publication 9
- 1.3 Related Documentation 10
- 1.4 Feature Overview 11
- 2 General Description 13
- Value Mnemonic Meaning 14
- 3 Internal Data Structures 17
- 4.1 System Functions 19
- 4.2 Timer Operation 19
- 5 Interface to MTP 21
- Section 5 Interface to MTP 22
- 6 Interface to Application 23
- 6.2.2 Receive Indication 24
- 6.5.1 Alerting Request 28
- 6.5.6 Confusion Request 32
- 6.5.7 Continuity Request 32
- 6.5.9 Exit Request 33
- 6.5.10 Facility Request 33
- 6.5.11 Facility Response 35
- 6.5.15 Information Request 37
- 6.5.19 Overload Request 40
- 6.5.21 Proceeding request 41
- 6.5.22 Progress Request 42
- 6.5.23 Release Response 43
- 6.5.24 Release Request 44
- 6.5.26 Resume Request 45
- 6.5.27 Segmentation Request 46
- 6.5.28 Setup Request 46
- 6.5.29 Setup Response 49
- 6.5.31 Suspend Request 52
- 6.6.1 Alerting Indication 56
- 6.6.6 Confusion Indication 60
- 6.6.7 Continuity Indication 61
- 6.6.9 Exit Indication 61
- 6.6.10 Facility Indication 62
- 6.6.11 Facility Confirmation 63
- 6.6.19 Overload Indication 68
- 6.6.21 Proceeding Indication 69
- 6.6.22 Progress Indication 70
- 6.6.23 Release Confirmation 71
- 6.6.24 Release Indication 71
- 6.6.26 Resume Indication 73
- 6.6.28 Setup Confirmation 74
- 6.6.29 Setup Indication 76
- 6.6.31 Suspend Indication 79
- 6.7 Parameter Definitions 80
- 6.7.1 Called Party Number 86
- 6.7.2 Calling Party Number 86
- 6.7.3 Cause Indicators 87
- 6.7.4 Custom Parameter 88
- 6.7.5 Message Data 88
- 6.7.7 Tariff Type 89
- 6.7.8 Unrecognised Parameter 90
- 6.8.3 Hop Counter Procedure 94
- 6.8.4 Continuity Testing 95
- Call Set Up 99
- Service 108
- 6.8.6 Message Segmentation 109
- 7 Management Interface 113
- reserved Set to zero 116
- 7.6 Local Overload Request 118
- Parameters 120
- 8 Non-Primitive Interface 121
- 8.3.1 Timer default values 138
- 8.5 Variant Initialisation 141
- operation 142
- message type 142
- 8.8 Read RAM Request 145
- 8.10 Read Circuit Request 146
- 8.11 Read Revision Request 146
- Section 150
- Event specific data 158
- Call states 164
- 8.22 Trace Event Indication 166
- A.1 German ISUP 171
- A.2 UK ISUP 172
- A.3 Japan (TTC) ISUP 173
- A.4 Nortel RLT 174
- A.4.2 Nortel RLT (ITU) 175
- A.5 Italian ISUP 176
- A.6 French ISUP 177
- A.7 China ISUP 178
- A.8 Finnish ISUP 180
- A.9 BICC 180
- Hex Dec Min Max 181
- Reference 181
- ISUP Module 183
- B.2 ITU-T Parameters 184
- B.3 ANSI T1.113 Messages 188
- B.4 ANSI T1.113 Parameters 189
- More Extended Options 195
- Appendix F: Timer Services 199
- F.1 Timer Expiry 200
- Variant Initialisation, 141 203
Produits connexes et manuels pour Communication Welltech Dialogic SS7 Protocols ISUP
(33 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.122 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels