Welltech Dialogic SS7 Protocols ISUP Manuel d'utilisateur Page 157
- Page / 203
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Dialogic
®
SS7 Protocols ISUP Programmer's Manual Issue 15
157
8.18 Send Selective Trace Event Mask Request
This message is issued by the ISUP module to enable additional diagnostic
information to be reported along with software and maintenance events for
debug purposes. Sends a mask indicating which selective trace events should
be active to the ISUP module. This message can be used to turn off some or
all software events or turn them back on again. The message may be sent
at any time after the initial per-module configuration message has been sent
to the ISUP module.
Message Header
structure MSG
type ISP_MSG_S_SELTRACE_MASK (0x5714)
id 0
src Originating module ID
dst ISUP module ID
rsp_req Sending layer's bit set if confirmation required
hclass 0x00
status 0x00
err_info 0x00
len 9
Parameter Area
parameters offset 0, size 9: mask Bits set to indicate selective trace events which
should be active
ISUP Response
method By sending a MSG
type 0x1714
SUCCESS status
ISP_BAD_PARAM
Parameters
mask
A bit mask indicating the selective trace events that are active. A ‘1’
indicates that an event is active and a ‘0’ indicates that it is not active. The
first octet sent is for selective trace event codes 0-7, the second octet for
selective trace event codes 8-15, etc.
Refer to
Section : 8.23 Selective Trace Event Indication on page 167 for a list
of selective trace events.
- Dialogic 1
- SS7 Protocols 1
- Contents 3
- Figures 6
- Revision History 7
- About this Publication 9
- 1.3 Related Documentation 10
- 1.4 Feature Overview 11
- 2 General Description 13
- Value Mnemonic Meaning 14
- 3 Internal Data Structures 17
- 4.1 System Functions 19
- 4.2 Timer Operation 19
- 5 Interface to MTP 21
- Section 5 Interface to MTP 22
- 6 Interface to Application 23
- 6.2.2 Receive Indication 24
- 6.5.1 Alerting Request 28
- 6.5.6 Confusion Request 32
- 6.5.7 Continuity Request 32
- 6.5.9 Exit Request 33
- 6.5.10 Facility Request 33
- 6.5.11 Facility Response 35
- 6.5.15 Information Request 37
- 6.5.19 Overload Request 40
- 6.5.21 Proceeding request 41
- 6.5.22 Progress Request 42
- 6.5.23 Release Response 43
- 6.5.24 Release Request 44
- 6.5.26 Resume Request 45
- 6.5.27 Segmentation Request 46
- 6.5.28 Setup Request 46
- 6.5.29 Setup Response 49
- 6.5.31 Suspend Request 52
- 6.6.1 Alerting Indication 56
- 6.6.6 Confusion Indication 60
- 6.6.7 Continuity Indication 61
- 6.6.9 Exit Indication 61
- 6.6.10 Facility Indication 62
- 6.6.11 Facility Confirmation 63
- 6.6.19 Overload Indication 68
- 6.6.21 Proceeding Indication 69
- 6.6.22 Progress Indication 70
- 6.6.23 Release Confirmation 71
- 6.6.24 Release Indication 71
- 6.6.26 Resume Indication 73
- 6.6.28 Setup Confirmation 74
- 6.6.29 Setup Indication 76
- 6.6.31 Suspend Indication 79
- 6.7 Parameter Definitions 80
- 6.7.1 Called Party Number 86
- 6.7.2 Calling Party Number 86
- 6.7.3 Cause Indicators 87
- 6.7.4 Custom Parameter 88
- 6.7.5 Message Data 88
- 6.7.7 Tariff Type 89
- 6.7.8 Unrecognised Parameter 90
- 6.8.3 Hop Counter Procedure 94
- 6.8.4 Continuity Testing 95
- Call Set Up 99
- Service 108
- 6.8.6 Message Segmentation 109
- 7 Management Interface 113
- reserved Set to zero 116
- 7.6 Local Overload Request 118
- Parameters 120
- 8 Non-Primitive Interface 121
- 8.3.1 Timer default values 138
- 8.5 Variant Initialisation 141
- operation 142
- message type 142
- 8.8 Read RAM Request 145
- 8.10 Read Circuit Request 146
- 8.11 Read Revision Request 146
- Section 150
- Event specific data 158
- Call states 164
- 8.22 Trace Event Indication 166
- A.1 German ISUP 171
- A.2 UK ISUP 172
- A.3 Japan (TTC) ISUP 173
- A.4 Nortel RLT 174
- A.4.2 Nortel RLT (ITU) 175
- A.5 Italian ISUP 176
- A.6 French ISUP 177
- A.7 China ISUP 178
- A.8 Finnish ISUP 180
- A.9 BICC 180
- Hex Dec Min Max 181
- Reference 181
- ISUP Module 183
- B.2 ITU-T Parameters 184
- B.3 ANSI T1.113 Messages 188
- B.4 ANSI T1.113 Parameters 189
- More Extended Options 195
- Appendix F: Timer Services 199
- F.1 Timer Expiry 200
- Variant Initialisation, 141 203
Produits connexes et manuels pour Communication Welltech Dialogic SS7 Protocols ISUP
(33 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels